Double tap to zoom

 

Features

SCREEN
KPI-JCI 5’ x 14’, 3-deck, 10o, wet vibrating screen
– V-belt drive assembly with 20-HP, 1800 RPM motor
– Huck-bolted assembly
– 5/16” plate steel side plates
– Two (2) 110-mm bearings
– External eccentric flywheels with bolt-in weights
– Eight (8) coil spring suspension system
– Side tension drawbar screen cloth retention system
(screen cloth is optional)
– Screen operates at 10o angle with a shaft speed of
approx. 900 rpm

FINE MATERIAL WASHER
KPI-JCI Model 5036-25S (36” single) fine material washer
– Tank is of 3/16” (sides and bottom) and 3/8” (rear end
plate) welded plate steel construction and includes a
curved bottom with integral rising current manifold (4”
dia. inlet)
– Large undisturbed pool area with adjustable weir boards
and overflow flume with 10” dia outlet
– Double pitch, solid flight spiral assembly with standard
AR steel inner wear shoes and standard urethane outer
wear shoes
– Greaseable, externally mounted Dodge Imperial E tail
end flange bearing; greaseable Dodge pillow block head
end bearing
– Lower end seal - chrome plated stainless steel wear
sleeve, water tight bellows type rubber seal and
secondary grease seal
– High efficiency v-belt drive assembly includes 15-HP
TEFC motor and Dodge TA-II double reduction shaft
mount reducer
– Tapered discharge chute set at 45o angle to grade
See Model 5036-25S Spec Sheet for additional information

CHASSIS
– Heavy duty 12” wide-flange beam construction
– Single axle arrangement with Dana 22,000# axle and
dual 11:00 x 22.5 tires (total of four)
– Fifth wheel king pin, air brakes, travel lights, mudflaps
and cribbing locations

WATER SYSTEM
– All fresh water plumbing to a single 6” inlet located near
the tail end of the fine material washer
– Fine material washer manifold includes a 4” butterfly
valve, 4” swing check valve and pressure gauge
– 1” chase water plumbing with gate valve
– Screen manifold with flow control valves for the spray
bars
– Twelve (12) spray bars each with nine (9) 7.0 gpm
(@40 psi) spray nozzles
– 3” connection on the screen manifold for the optional
feed box

SCREEN CHUTES / FINES HOPPER
– 3/16” A36 welded plate steel construction
– Chutes allow for positioning of three (3) radial stackers
under the chutes
– Fines hopper transitions to form the feed box and baffle
plate of the 36” single fine material washer

ACCESS
– 24” wide access platform with 1-1/2” OD handrails and
toeboards across the feed end and both sides of the
screen
– Ladder access from grade which can be located on either
side of the plant

PHYSICAL / OPERATING CHARACTERISTICS
– Feed Material Size - Typically 6” minus
– Capacity - Approximately 200 TPH (dependent on feed
gradation and desired products)
– Water Requirements - Up to 700 gpm (dependent on
feed gradation and desired products)
– Travel Dimensions
        Length 36’-4” overall / 29-5” king pin to axle
        Width 11’-3”
        Height 13’-8”
– Operating Dimensions
        Length 35’-9” overall
        Width 11’-6”
        Height 17’ without feed box / 19’-10” with feedbox
– Loads
        King Pin 14,700 lbs
        Axle 18,800 lbs
       Overall 33,500 lbs
Note individual plant weights will vary dependent on
options included

Specifications

Model

Screen Size
(ft x ft / m x m)

Fine Material Washer Size
(in x ft / mm x m)

Blademill Size
(in x ft / mm x m)

Water Requirements
(USGPM)

1814P

5 x 14 / 1.5 x 4.2
(incline)

36 x 25 / 914 x 7.6
(single)

n/a

700

0.99% Financing for 48 Months

Check out our financing special offering 0.99% for 48 months!