Double tap to zoom

 

Features

SCREEN
KPI-JCI 5’ x 14’, 3-deck, 10o, wet vibrating screen
– V-belt drive assembly with 20-HP, 1800 RPM motor
– Huck-bolted assembly
– 5/16” plate steel side plates
– Two (2) 110-mm bearings
– External eccentric flywheels with bolt-in weights
– Eight (8) coil spring suspension system
– Side tension drawbar screen cloth retention system (screen cloth is optional)
– Screen operates at 10o angle with a shaft speed of approx. 900 rpm

FINE MATERIAL WASHER
KPI-JCI Model 5036-25S (36” single) fine material washer
– Tank is of 3/16” (sides and bottom) and 3/8” (rear end plate) welded plate
steel construction and includes a curved bottom with integral rising current
manifold (4” dia. inlet)
– Large undisturbed pool area with adjustable weir boards
and overflow flume with 10” dia outlet
– Double pitch, solid flight spiral assembly with standard AR steel inner wear
shoes and standard urethane outer wear shoes
– Greaseable, externally mounted Dodge Imperial E tail end flange bearing;
greaseable Dodge pillow block head end bearing
– Lower end seal - chrome plated stainless steel wear sleeve, water tight
bellows type rubber seal and secondary grease seal
– High efficiency v-belt drive assembly includes 15-HP
TEFC motor and Dodge TA-II double reduction shaft
mount reducer
– Tapered discharge chute set at 45o angle to grade
See Model 5036-25S Spec Sheet for additional information

STRUCTURAL SUPPORT
– Steel 8” wide-flange support columns and 8” wide-flange
skid runners on each side
– Broken down for shipment and match-marked for ease
of assembly in the field

WATER SYSTEM
– All fresh water plumbing to a single 6” inlet located near
the tail end of the fine material washer
– Fine material washer manifold includes a 4” butterfly
valve, 4” swing check valve and pressure gauge
– 1” chase water plumbing with gate valve
– Screen manifold with flow control valves for the spray bars
– Twelve (12) spray bars each with nine (9) 7.0 gpm
(@ 40 psi) spray nozzles
– 3” connection on the screen manifold for the optional
feed box

SCREEN CHUTES / FINES HOPPER
– 3/16” A36 welded plate steel construction
– Chutes allow for positioning of three (3) radial stackers
under the chutes
– Fines hopper transitions to the feed box of the 36” single
fine material washer

ACCESS
– 24” wide access platform with 1-1/2” OD handrails
and toeboards across the feed end and both sides of
the screen
– Ladder access from grade which can be located on either
side of the plant

PHYSICAL / OPERATING CHARACTERISTICS
– Feed Material Size - Typically 6” minus
– Capacity - Approximately 200 TPH (dependent on feed
gradation and desired products)
– Water Requirements - Up to 700 gpm (dependent on
feed gradation and desired products)
– Operating Dimensions
Length 37’-9-1/2” overall
Width 11’-6”
Height 17’-7” without feed box / 20’-5” with feedbox
– Loads
Overall 32,300 lbs
Note individual plant weights will vary dependent on
options included

Specifications

Model

Screen Size
(ft x ft / m x m)

Fine Material Washer Size
(in x ft / mm x m)

Blademill Size
(in x ft / mm x m)

Water Requirements
(USGPM)

1814S

5 x 14 / 1.5 x 4.2
(incline)

36 x 25 / 914 x 7.6
(single)

n/a

700

0.99% Financing for 48 Months

Check out our financing special offering 0.99% for 48 months!